Product Description
Ampire CAC300 Can bus adapter
With this CAN bus interface you can read from three different CAN bus systems in the vehicle all the relevant lines you need to install car accessories, car alarm systems and remote start systems from the corresponding CAN bus systems of modern cars and also The most important alarm and comfort functions also control. The CAC300 CAN bus interface can be installed in a wide range of vehicles and ground pulsed from any car alarm or remote control on the market.
Prior to installation, vehicle specific firmware must be loaded into the CAC300 using a PC via the BL600 programming interface. We can do this for free if you specify the exact vehicle type when placing your order. However, we always recommend that you flash the firmware during installation. Wiring is very simple. Apart from the 12 volt operating voltage, only the two CAN bus lines need to be connected. There are separate connection cables for all inputs and outputs.
OVERVIEW OF CONTROLLED FUNCTIONS
INDEX
– If 12 volts DC is present at this input, the vehicle's turn signals are turned on.
CONVENIENT LOCKING FROM THE VEHICLE
– When ground is applied to this input, all doors, windows and sunroof will close.
OPEN THE CENTRAL LOCKING OF THE DRIVER'S DOOR
– If there is a ground on this input, only the driver's door will open.
OPEN CENTRAL LOCKING OF ALL DOORS
– If there is ground on this input, all doors will open.
OPEN TRUNK
– When there is a ground on this input, the electrical trunk opens.
CLOSE ALL POWER WINDOWS
– If ground is applied to this input, all windows close after 1.5 seconds.
START THE ENGINE
– If there is ground on this input, the motor starts
STOP ENGINE
– If there is a ground on this input, the motor is switched off
DRIVER'S DOOR CONTACT SIMULATION
– If there is a ground on this input, opening the driver's door is simulated in the CAN.
OVERVIEW OF PROPORTIONATE EXPENSES
FOOT BRAKE
– When you step on the foot brake and the ignition is on, there is 12 volts DC at the output.
CENTRAL LOCKING (alternative)
– Vehicle-specific output for central locking control.
INDICATOR (alternative)
– Vehicle specific output for checking vehicle indications.
ACCESSORY
– After inserting the vehicle key into the ignition lock, the output is 12 volts DC.
IGNITION
– After the ignition is turned on, there is 12 volts DC at this output.
ENGINE SPEED
– When the motor is running, there is a speed (RPM) signal at the output.
ENGINE OFF
– When the ignition is on and the engine is off, there is a ground at the output.
SPEED
– If the vehicle is moving above 10 km/h, there is a ground on the output and it only turns off when the ignition is off.
PARKING BRAKE (P FOR AUTOMATIC)
– When the ignition is on and the parking brake is applied (P for automatic), there is a ground at the output.
SEQUENCE CHANGE
– There is a ground at the output when a programmed series of switches has been pressed.
CENTRAL LOCKING OPEN WITH FACTORY REMOTE CONTROL
– A 500ms mass pulse is present at the output after opening with the factory remote.
CENTRAL LOCKING LOCKING WITH FACTORY REMOTE CONTROL
– A 500ms mass pulse is present at the output after closing with the factory remote control.
EXIT STATUS
– After locking with the factory remote, there is a ground at the output.
ALARM FROM FACTORY ALARM SYSTEM
– In case of an alarm from the factory alarm system, there is a ground at the output.
COMMUNICATION BONNET
– When the hood is opened, there is a ground at the outlet.
TRUNK CONTACT
– When the trunk opens, there is a ground at the output.
COMMUNICATE REMAINING DOORS
– When the remaining doors are opened, there is a ground at the output.
DRIVER'S DOOR COMMUNICATION
– When the driver's door is opened, there is a ground at the output.
OTHER CONNECTIONS
– CAN1 low data flow bus connection
– CAN1 High data bus connection
– CAN2 low data flow bus connection
– CAN2 High data bus connection
– CAN3 low data flow bus connection
– CAN3 High data bus connection
- Dimensions
– Permanent plus 12 volt DC
TECHNICAL SPECIFICATIONS
– Operating voltage: 12 volts DC
– Quiescent current: 0.9 mA
– Operating current: 28-40mA
– Number of analog inputs: 10
– Number of analog outputs: 18
– Output load capacity: 50mA
– Number of supported CAN buses: 3
– Read speed: 33.33 kb/s, 500 kb/s
– Dimensions: 85x35x15mm
– Weight: 93g
– Operating temperature: -40°C +85°C
FIELD OF DELIVERY
– CAN bus controller
– wiring
ECE MARK
– E20 97R01/08 004015 00
IMPORTANT NOTE
Check which vehicles are compatible. Not all functions are technically possible in all vehicles and of course depend on the equipment. After installation, check for malfunctions